電動砂當量試驗儀，

額定功率:180W

自控定時:30S/次 外形尺寸:560×320×360

配重活塞:1kg±5g

圓柱形塑料試筒:

內徑:32mm±0.25mm 高度:420mm±0.25mm

沖洗管外徑:6mm±0.25mm 內徑:4mm±0.2mm

試驗步驟 

1,試驗 為了不影響沉淀的過程,試驗必須在無擾動的水平臺上進行.隨時檢查試驗的沖洗管口,防止堵塞.試驗過程中,沖洗液的溫度應保持20±2℃范圍內.由于塑料在太陽下容易變成不透明,應盡量避免將塑料器皿直接暴露在太陽下.盛試驗溶液的塑料器皿用畢要清洗干凈.

(1)用沖洗管將沖洗液吸入試筒直到100mm刻度(約80毫升).

(2)把相當于120±1g干料重的濕樣用漏斗倒入豎立試筒中.

(3)反復敲打試筒下部,以除去氣泡使試樣濕潤,靜置10min.

(4)試樣靜置10±1min結束后,用橡膠塞堵住試筒,將試筒水平固定在振蕩器上.(注意試筒底部方頭碰螺絲.)

(5)開動振蕩器,在30±1S的時間內振蕩90次.用人工振蕩時,要用手將試筒橫向水平放置,僅需手腕振蕩,不必晃動手臂,振幅為203±25mm,振蕩時間和次數與振蕩器相同.然后將試筒取下,豎直放回試驗臺上,擰下橡膠塞.

(6)將沖洗管插入試筒中,用沖洗液迅速沖洗附在試筒壁上的集料,然后將沖洗管插到試筒底部,慢慢轉動沖洗管,同時勻速緩慢提高沖洗管,使附著在集料表面的細粒雜質浮上來,直至溶液達到380mm刻度線為止.

(7)緩慢勻速向想拔出沖洗管,當液面位于380mm刻度線時,切斷沖洗管的液流,使液面保持380mm刻度線,然后在沒有擾動的情況下靜置20min±15S.

注意事項 

1,試驗完畢后,須將活塞擦洗干凈.

2,避免圓形試筒磕碰.

3,定期向振蕩器滑動桿上注潤滑油

安徽合肥市路達儀器建材有限公司主營、建筑儀器、瀝青儀器、土工儀器、水泥實驗儀器、分析儀器、測繪儀器、實驗室成套設備、攪拌站成套設備。我公司有多名維修人員為您確保售后及維修設備，另我公司對外出租成套實驗儀器設備。；手機；李。